收藏本站
R E(WH)
R E(VH)
+15 V
R E(UH)
Gating WH
R BS
D BS
C BS
C BSC
(19) V B(W)
(18) V CC(WH)
(17) IN (WH)
(20) V S(W)
VB
VCC
COM
IN
OUT
VS
P (27)
W (26)
R BS
D BS
(15) V B(V)
(14) V CC(VH)
VB
Gating VH
C BS
C BSC
(13) IN (VH)
(16) V S(V)
VCC
COM
IN
OUT
VS
V (25)
M
M
C
U
Gating UH
R BS
R F
D BS
C BS
C BSC
(11) V B(U)
(10) V CC(UH)
(9) IN (UH)
(12) V S(U)
VB
VCC
COM
IN
OUT
VS
U (24)
C DCS
Vdc
+5 V
Fault
R S
R PF
C SC
C FOD
(8) C SC
(7) C FOD
(6) V FO
C(SC) OUT(WL)
C(FOD)
VFO
N W (23)
R SW
Gating WL
(5) IN (WL)
IN(WL) OUT(VL)
Gating VL
(4) IN (VL)
IN(VL)
N V (22)
R SV
(3) IN (UL)
Gating UL
(2) COM
IN(UL)
C BPF
C PF
(1) V CC(L)
COM
VCC
OUT(UL)
V SL
N U (21)
R SU
C SP15
C SPC15
Input Signal for Short-
Circuit Protection
W-Phase Current
V-Phase Current
U-Phase Current
R FW
R FV
R FU
C FW
C FV
C FU
Figure 11. Typical Application Circuit
4th Notes:
1. To avoid malfunction, the wiring of each input should be as short as possible (less than 2 - 3 cm).
2. By virtue of integrating an application-specific type of HVIC inside the Motion SPM ? 3 product, direct coupling to MCU terminals without any optocoupler or transformer isola-
tion is possible.
3. V FO output is open-collector type. This signal line should be pulled up to the positive side of the 5 V power supply with approximately 4.7 k ? resistance (please refer to Figure
9).
4. C SP15 of around seven times larger than bootstrap capacitor C BS is recommended.
5. V FO output pulse width should be determined by connecting an external capacitor (C FOD ) between C FOD (pin 7) and COM (pin 2). (Example : if C FOD = 33 nF, then t FO = ???? ms
(typ.)) Please refer to the 2nd note 5 for calculation method.
6. Input signal is active-HIGH type. There is a 3.3 k ?? resistor inside the IC to pull down each input signal line to GND. When employing RC coupling circuits, set up such RC cou-
ple that input signal agree with turn-off / turn-on threshold voltage.
7. To prevent errors of the protection function, the wiring around R F and C SC should be as short as possible.
8. In the short-circuit protection circuit, please select the R F C SC time constant in the range 1.5 ~ 2 ? s.
9. Each capacitor should be mounted as close to the pins of the Motion SPM 3 product as possible.
10. To prevent surge destruction, the wiring between the smoothing capacitor and the P & GND pins should be as short as possible. The use of a high-frequency non-inductive
capacitor of around 0.1 ~ 0.22 ? F between the P & GND pins is recommended.
11. Relays are used in almost every systems of electrical equipment in home appliances. In these cases, there should be sufficient distance between the MCU and the relays.
12. C SPC15 should be over 1 ? F and mounted as close to the pins of the Motion SPM 3 product as possible.
?2006 Fairchild Semiconductor Corporation
FSBB20CH60 Rev. C6
12
www.fairchildsemi.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
FSBB30CH60F IC SMART PWR MODULE SPM27-EA
FSBF10CH60BTL MODULE SPM 600V 10A 3PH SPM27-JB
FSBF10CH60BT MODULE SPM 600V 10A 3PH SPM27-JA
FSBF10CH60B MODULE SPM 600V 10A 3PH SPM27-JA
FSBF15CH60BTH MODULE SPM MOTION CTRL SPM27-JC
FSBF3CH60B MODULE SPM 600V 3A 3PH SPM27-JA
FSBF5CH60B MODULE SPM 600V 5A 3PH SPM27-JA
FSBS15CH60F MODULE SPM 600V 15A SPM27-BA
相关代理商/技术参数
FSBB3 制造商:MMD 制造商全称:MMD Components 功能描述:HC-49/US Surface Mounted Crystal
FSBB30CH60 功能描述:马达/运动/点火控制器和驱动器 600V 30A SMART RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
FSBB30CH60_0503 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Smart Power Module
FSBB30CH60B 功能描述:马达/运动/点火控制器和驱动器 600V -30A 3-phase RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
FSBB30CH60C 功能描述:马达/运动/点火控制器和驱动器 600V 30A SPM RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
FSBB30CH60CM 制造商:Fairchild 功能描述:30A SPM3V V4 14.0mm lead lengt
FSBB30CH60CT 功能描述:马达/运动/点火控制器和驱动器 30A SPM3V Inverter RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
FSBB30CH60F 功能描述:马达/运动/点火控制器和驱动器 HIGH_VOLTAGE RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube